LambdaCANp Kit

(CAN Output)

MPN: LCANp-XX Category:

ECM’s LambdaCANp Module is a powerful, “next-generation” wideband Lambda (λ) measurement module with a CAN interface.  In addition to providing outstanding measurement range and accuracy, LambdaCANp addresses the two principle sources of error with wideband sensor use: sensor aging and pressure sensitivity.  All wideband sensors and pressure sensors supplied are factory-calibrated and this calibration is stored in a memory chip in the sensor’s connector.  For best accuracy over the life of the wideband sensor, calibration can be quickly performed using ambient air.  This recalibration is stored in the memory chip and stays with the sensor.  Sensors can be tested and recalibrated in a central location and distributed to users, ensuring consistent results throughout a large test facility.  Pressure compensation (P-COMP™) improves accuracy at non-stoichiometric (i.e.  λ ≠ 1) and non-atmospheric (i.e.  P ≠ 101 kPa) conditions.  For example, a pressure increase of only 34 kPa will cause an error of 0.58 λ at λ = 3.  Pressure compensation eliminates this error and enables innovative applications such as %O2 measurements in intake manifolds.  Pressure data is available on the CAN bus.

LambdaCANp will work with all NTK and Bosch-type wideband sensors.  It is programmable for all fuel types (H:C, O:C, N:C ratios and H2).  LambdaCANp outputs λ, AFR, FAR, ϕ, %O2, pressure, and all sensor parameters including pumping current, control voltages, temperature (via cell resistance), and sensor age factor.  Three optional displays, two with programmable analog outputs are available.  These displays can used with one or two modules.


Response Time Less than 150 ms
Fuel Type Programmable H:C, O:C, and N:C ratios, and H2
Power 8 to 28 VDC, AC/DC (optional), 5A (max. 1min. surge), 1.2A (steady-state)
Sensor Mounting Wideband: 18mm x 1.5mm thread
Pressure: 1/4" NPT/ISO
Dimensions Module: 145mm x 120mm x 40mm, Environmentally Sealed
Sensor Cable: 0.5m (sensors), +2m (standard), +3m (optional)
Operating Temperature Electronics: -55 to +125°C, IP67
Sensor: 850°C (maximum continuous)
Ranges & Accuracies
λ 0.4 to 25 (± 0.6% at stoichiometric, ± 0.9% average elsewhere)
AFR 6 to 364 (± 0.6% at stoichiometric, ± 0.9% average elsewhere)
F/A 0.003 to 0.167 (± 0.6% at stoichiometric, ± 0.9% average elsewhere)
φ 0.04 to 2.5 (± 0.6% at stoichiometric, ± 0.9% average elsewhere)
O2 0 to 25% (± 0.1%)
Pressure SAE: 0 to 75 psia (± 0.1 psia)
Metric: 0 to 517 kPa (± 0.7 kPa)
CAN CAN2.0A. Compliant with ISO 11898.
Configurable via CAN using ECM's Configuration Tool software.

Included Kit Components

The base kit includes the following:

Filters Sort results


The base kit will include one of the follow sensors based on your sensor type selection:

Filters Sort results


Pressure Compensation (SAE version) option adds the following:

Filters Sort results


Pressure Compensation (Metric version) option adds the following:

Filters Sort results


Calibration Tools

Filters Sort results


LambdaCAN Module Configuration Software Manual (Ver. 2014-01-28, 2 MB)
LambdaCANp Manual (Ver. 2014-09-11, 1 MB)
Vboost Power Supply Brochure (162 KB)
Firmware Update Procedure for Modules (220 KB)
ECM Configuration Tool (Ver. 4.48.20, 30 MB)
TechNote Engine Stoichiometry (66 KB)